High build repair mortar, conforms to EN1504-3 class R3

Renderoc HB40 is a high build repair mortar for localised repair of reinforced concrete up to 45MPa. Meets the requirements of EN1504-3 Class R3. It can be applied to vertical concrete patches up to 40 mm deep. Suitable for use with Galvashield anode protection systems.

Typical Applications

• Vertical & overhead patch repairs

• Localised trowel or wet spray application

• Up to 1m2 repair area

• Trowel build depth between 10-40mm required

Required strength is between 25-40 MPa

Advantages

• Compatible with concrete strength in the range 30 to 45MPa

• Abrasion resistant - suitable for aggressive environments

• Shrinkage compensated - provides long term dimensional stability

• Low permeability to potentially damaging water, CO2 and chloride ions

• Suitable for use with Galvashield anodes

• Can be applied using wet-spray process - providing faster high build repairs

• Pre-bagged to overcome site-batched variations - only the site addition of clean water required

• Complies to AS/NZS4020:2018 - suitable for use in potable water

High build repair mortar, conforms to EN1504-3 class R4

Renderoc HB70 is a high build repair mortar for localised repair of reinforced concrete > 45MPa. Meets the requirements of EN1504-3 Class R4. It can be applied to vertical concrete patches up to 40 mm deep. Suitable for use with Galvashield anode protection systems.

Typical Applications

• Vertical & overhead patch repairs

• Localised trowel or wet spray application, up to 1m2 repair area

• Trowel build depth between 5-40mm required, and required strength >45 MPa

• Compatible with concrete strength > 45MPa

Advantages

• High strength - suitable for structural repairs

• Abrasion resistant - suitable for aggressive

• environments

• Shrinkage compensated - provides long termdimensional stability

• Low permeability to potentially damaging water, CO2and chloride ions

• Suitable for use with Galvashield anodes

• Can be applied using wet-spray process - providingfaster high build repairs

• Pre-bagged to overcome site-batched variations - only the site addition of clean water required

• Complies to AS/NZS4020:2018 - suitable for use in potable water

High strength, free flowing micro concrete repair mortar conforming to EN1504-3 Class R4.

Renderoc LA55 Plus is a high strength, fluid micro-concrete for large volume structural repairs at a nominal thickness up to 500 mm. Meets the requirements of EN1504-3 Class R4.

Typical Applications

Deep section patch repair using form pour or pump, all orientations, section depth between 50-500mm, and requiring high strength, between 30-75 MPa

Advantages

• Can be applied in sections up to 500 mm thick

• Achieves 75 MPa @ 56 days

• Maximum compatibility with concrete compressive strength, 30-75 MPa

• Unique dual expansion system offers an extremely high level of control of plastic and long-term drying shrinkage

• Low alkali content minimises risk of alkali-silica reaction

• Excellent bond to concrete substrates without independent primer

• Extremely low permeability provides excellent protection against carbon dioxide and chlorides

• Enhanced durability - Meets the requirements of durability to RMS B80 concrete specification

• Sustainable product with low carbon footprint and reduced emissions of greenhouse gases

• Exceptional flow allows pumping or pouring into restricted locations

• Pre-bagged to overcome site-batched variations - only the site addition of clean water is required

• Pre-bagged to overcome site-batched variations - only the site addition of clean water is required

• Contains no chloride admixtures

Fairing Mortar

Renderoc FC cementitious fairing coat is designed for application in thin layers up to 3 mm, to produce a fair-faced appearance to concrete surfaces or masonry surfaces in readiness to receive a protective/decorative coating. Renderoc FC is RCS (Respirable Crystalline Silica) Hazard Free. Not hazardous in accordance with Australian Inventory of Industrial Chemicals. Contains <0.1% RCS.

Typical Applications

Surface repair vertical/overhead

Advantages

• Excellent bond to the concrete substrate

• Easy to use - no independent primer or curing membrane necessary

• Pre-blended to overcome site-batched variations - only the site addition of clean water is required

• Contains no chloride admixtures

General purpose, high flow, shrinkage compensated grout.

Conbextra GP is a general-purpose shrinkage compensated (Class A) cementitious, flowable or trowellable grout for gap thicknesses from 10 mm up to 100 mm. Conbextra GP has a 28-day compressive strength of 65 MPa when mixed at trowellable consistency.

Typical Applications

• General site grouting where higher compressive strength is required

Advantages

• High ultimate strength and low permeability ensure the durability of the hardened grout

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state

• Can be dry packed, rammed, trowelled, poured and pumped

• Pre-packaged material overcomes potential on-site mixing variations

• Develops high early strength without the use of chlorides

• No metallic iron content to cause staining

• Complies to AS/NZS 4020:2005 Products in Contact with Potable Water

Large area, internal and external pavement repair mortar, 15-50mm deep.

Paveroc is used for the reinstatement between 15mm and 50mm thick of areas of concrete pavements and floors up to 18sq.metres. The rapid strength gain of Paveroc will ensure that down-time is significantly reduced. It may be used internally and externally.

Typical Applications

• Floor, pavement or joint concrete repairs, large area repair up to 18sq. metres, trowel application, requiring trafficability in 16 hours, where section depth is between 15-50mm

Advantages

• Rapid strength gain - will generally accept pedestrian traffic at 16 hours

• High strength, abrasion and weather resistance

• Single component product eliminates site batching and requires only the site addition of clean water

• Excellent bond to the concrete substrate

• Shrinkage compensated

• Contains no chloride admixtures

Curing membrane for Fosroc Renderoc and primer for Fosroc Patchroc and Paveroc

Nitobond AR is a single component polymer emulsion system used as a curing membrane for cementitious repair products.
Nitobond AR can also be used as a bonding agent for Patchroc and Paveroc products.

Typical Applications

• Curing membrane for Renderoc repairs

Primer for Patchroc and Paveroc repair mortars

Advantages

• Single component - no site mixing

• Easy to use - ready to use straight from container

• Cost effective - economical in use

• Effective curing membrane for Renderoc repair mortars

Primer for Fosroc Renderoc repair mortars

Nitobond HAR is a single component polymer emulsion system designed as a bonding agent for Renderoc repair products

Typical Applications

• Primer for the Renderoc cementitous repair system

Advantages

• Single component - no site mixing

• Easy to use - ready to use straight from container

• High bond strength - excellent bond strength between Renderoc systems and concrete

• Non-flammable

High performance primer for Cemtop cementitious flooring systems and other cement-based flooring products. (Previously known as Durafloor Level Prime)

Concentrated primer for Cemtop GP Advanced & Cemtop XD. Seals the substrate to prevent pinholes, promote adhesion and help prevent desiccation of the floor topping.

Typical Applications

• Primer for Cemtop GP Advanced & Cemtop XD

• Primer for Paveroc, Patchroc C and Patchroc GP

Advantages

• Excellent adhesion to concrete and cementitious screeds

• Seals the substrate to minimise pin holing

• Excellent water resistance after film formation

• Economic, easy to use with no restrictive pot life

NB - Image shown is a 5L option

Aliphatic alcohol evaporative retarder

Concure AV is an aliphatic alcohol evaporative retarder used during the placement of fresh concrete to greatly reduce cracking caused by unfavourable weather conditions. Supplied as a concentrate which is diluted on site with water.

Typical Applications

• All types of flat concrete applications

• Machine or hand finished

• Including stamped concrete

Advantages

• Reduces and often eliminates the formation of shrinkage cracks in plastic concrete

• Gives superior finishing properties during unfavourable weather conditions

• Maintains a plastic and workable surface

• Prevents surfaces crusting